Why is My Blink Camera Flashing Red? – Complete Guide 2023

Blink Outdoor is a cordless, battery-powered HD security camera that gives you infrared night vision so you can watch over your house at any time of day. Blink cameras have a long battery life and can operate for up to two years with two AA lithium batteries. They are a great choice of cameras for home security purposes. 

Blink does a good job when it comes to exterior security cameras, but sometimes even the best technology can face problems. A red flashing light indicates that your camera has a problem. Several blinking lights, including a flashing red light, may be visible when utilizing the Blink Outdoor Camera.

There could be different reasons why these lights are flashing red. If you are wondering Why Your Blink Camera Flashing Red? Then you are at the right place. Keep reading to find out how to fix the blink camera red light issue.

blink camera flashing red
Blink Camera

Why Is My Blink Camera Flashing Red?

The red flashing light on your Blink Outdoor Camera may indicate that your camera is not up and running or perhaps a new battery is required. In short, the Blink Camera will flash red due to some problem with the device. Some of the causes behind this problem are listed down below:

1. Blink Camera Has Lost Internet Connection

One of the obvious and simplest reasons why your blink camera won’t work or show red light is because it has lost the connection to the internet. By unplugging your router, waiting a few seconds, and then plugging it back in, the router will restart. Make sure to check your router to see whether it has an active internet connection. 

When your Blink camera isn’t connected to the internet it will blink its red light. The blinking camera red light will stop flashing once you have connected to an active internet connection. If it still shows red light after the internet connection is restored, then try to reset your blink camera. 

2. Blink Camera Has Low Battery

Like any other electronic device, low battery levels will end up showing a red light on your device. After the blue recording light fades, Blink Support asserts that the camera will flash red light five to six times. After that, your camera won’t produce any light at all, which is an obvious sign that the batteries are dead.

The red light will be short and continuous if the internet has been lost, whereas the red light will be different if your batteries have died. If there is a problem with the battery, the camera will flash solid red a little more slowly a few times before going out.

3. Blink Camera Has Detected Motion

Many Blink cameras with motion detection flash their red light indicator when any motion is detected. This setting can be changed. But some people prefer to have it on so they can see if motion-detecting cameras are functioning properly. 

4. Blink Camera is Setting Up

A flashing red light on your Blink outdoor camera is simply letting you know that the initialization and setup process is still in progress.

This blinking red indicator should only appear briefly at the start of the startup process before giving way to a blinking green light which will then be followed by a solid blue light.

5. Blink Camera Requires a Reset

Sometimes Blink camera issues are simply not worth trying to figure out. It’s always safe to simply reset your camera if it is suddenly blinking red. This can frequently save you a tonne of time when debugging errors. You can keep reading the article to find out how to reset your blink camera.

How to Fix Blink Camera Flashing Red?

Down below, we have listed a bunch of fixes to help you fix your blink camera flashing red. Make sure to try each step and check if your blink camera red light has been fixed or not.

1. Ensure Your Camera Is Connected to the Internet

Your blink camera might show a slow and continuous red light if it doesn’t have an internet connection. It is easy to connect your Blink Outdoor Camera to Wi-Fi, which should immediately stop the red light from flashing. Follow these steps to connect your Blink Outdoor Camera to the internet:

  • First, establish a Wi-Fi connection between the Blink Outdoor Camera and the Sync Module. The network should be called “BLINK-” and contain a serial number that you may use to connect.
  • To establish a connection, tap Join.
  • Add your own WiFi network now by selecting your Wi-Fi name from the list of detected Wi-Fi networks.
  • Enter your  WiFi password.
  • Tap on the Done button which should now be visible on the screen, indicating that the network configuration was successful.

2. Power Cycle Your Blink Camera

Your Blink camera’s red light may stop blinking if you reboot it occasionally. Rebooting is sometimes the easiest answer to all electronic problems. 

Try this method and see whether it assists you in fixing the problem. However, if you have already tried this and are still receiving the error, then we strongly suggest that you carry out the additional fixes in this guide.

3. Replace The Batteries

If the other two fixes haven’t worked for you, the batteries might be low and that would explain why the red indicator was blinking. Check the type of batteries in your own camera and get a new set because batteries for each brand of blink camera may vary. 

Simply open the container and remove the batteries. Put in the new batteries that you just bought for your camera. Once finished, check that the battery pole is properly positioned, then replace the top compartment.

People often wonder what could make blink cameras even better. Who knows? Maybe a Detachable Camera Flash could do the trick Let us know your thoughts on what could make enhance the experience with blink cameras.

Why Won’t My Blink Camera Connects to My Sync Module

If your Blink camera is not connecting to your sync module, there are several possible reasons and troubleshooting steps you can try:

  1. Check the proximity: Make sure your Blink camera is within range of the sync module. The recommended range is typically up to 100 feet (30 meters) in an open area. If the camera is too far away, try moving it closer to the sync module and see if it establishes a connection.
  2. Verify sync module status: Check the status of your sync module. Ensure that it is powered on and connected to your Wi-Fi network. You can try restarting the sync module by unplugging it from the power source, waiting for a few seconds, and plugging it back in.
  3. Check Wi-Fi signal strength: Weak Wi-Fi signal can prevent the camera from connecting to the sync module. Verify that the sync module is within range of your Wi-Fi network and try moving it closer to the router or using a Wi-Fi extender to improve the signal strength.
  4. Ensure the sync module is not overloaded: If you have multiple Blink cameras connected to the sync module, there might be too many devices for it to handle. Consider reducing the number of connected cameras or adding an additional sync module to distribute the load.
  5. Check for interference: Other devices or appliances in your home may be causing interference with the connection between the camera and sync module. Try moving the sync module away from potential sources of interference, such as cordless phones, baby monitors, or microwave ovens.
  6. Verify Wi-Fi network settings: Ensure that the Wi-Fi network settings on the sync module are correct. Check the SSID (network name) and password to make sure they match your Wi-Fi network credentials. You can check and update these settings using the Blink mobile app.
  7. Re-sync the camera: If the camera is still not connecting to the sync module, you can try re-syncing it. Follow the instructions in the Blink camera’s user manual or the official Blink support website to remove the camera from your account and then re-add it as a new device.

Read Also: How to Fix  Roku Blinking White Light?

FAQs

How to turn off Red Light on Blink Camera?

In case the red light is not turning off then you need to reset the Blink camera. For this, you need a pin or any thin object. Press the reset button and wait till the red light turns blue or green.

How do I get my blink camera to stop blinking red?

To stop Blink Camera from blinking red first you need to identify the cause of blinking red. The first reason could be that your Blink camera is not connected to the internet or Blink camera has a low battery. So make sure that your blink camera is properly charged and connected to the internet.

How do I make my Blink camera stay on live?

You need to follow the below steps to make your Blink camera stay live
1. First click on the live view on the home screen.
2. On the bottom right corner, press the More menu button.
3. Go to Device settings and turn off the live view option.

Can you turn light off on Blink camera?

Yes, you can turn the light off on your blink camera. All you need is to follow the below steps
1. Launch the Blink app on your smartphone
2. Go to the Camera Settings menu
3. Diable the light status.
4. The light will no longer display the blue LED when recording.

Why is my blink camera flashing red and not connecting?

Your blink camera is flashing red because it is not connected to the internet. To fix this, disconnect and re-plug the Mini camera. If the Mini Camera had previously connected to your network, the red led light will change to solid blue and flash green when it reconnects.

How do I get my Blink camera back online?

To get your Blink camera back online, you can follow these troubleshooting steps:
1. Check the power source
2. Check the Wi-Fi connection
3. Restart the camera
4. Restart the sync module
5. Check the network settings
6. Reset and re-sync the camera

Why is my Blink camera flashing red?

If your Blink camera is flashing red, it typically indicates that there is an issue with the camera or its connectivity. Here are a few possible reasons and solutions:
1. Low battery
2. Weak Wi-Fi signal
3. Wi-Fi network issue
4. Sync module issue
5. Camera connectivity issue

What do the colors on a Blink camera mean?

The Blink cameras use different LED light colors to indicate various statuses. Here’s a general overview of the different colors and their meanings:
1. Blue: A solid blue light indicates that the Blink camera is recording or streaming live video.
2. Green: A solid green light typically means the camera is powered on and connected to the Blink sync module or Blink Mini hub.
White: A solid white light indicates that the camera is armed and ready to detect motion or start recording.
3. Red: A solid red light often indicates that there is an issue with the camera or its connectivity. It could indicate a low battery, weak Wi-Fi signal, or connection problem with the sync module.
4. Yellow: A solid yellow light usually indicates that the camera is in setup mode and ready to be added to your Blink system. It is often seen during the initial setup process.
5. Off: If the camera’s LED light is off, it usually means the camera is not powered on or does not have a connection to the sync module or Wi-Fi network.

Conclusion

When it comes to security, blink cameras have so far done a very good job. People ask ‘why is my blink camera flashing red?’ There could be multiple answers. It could be due to the batteries running out or the camera isn’t connected to the internet. You can try replacing the batteries or ensuring that your camera is connected to the internet. Try power cycling if nothing else works.

Read Also:

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *